Toshiba Tosvert VF-AS1 Manual de usuario Pagina 148

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 312
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 147
E6581301
F-36
6
6.22 Setting motor constants
H : Auto-tuning 1
H
: Slip frequency gain
H
: Auto-tuning 2
H
:
Motor rated capacity (motor nameplate)
H :
Motor rated current (motor nameplate)
H :
Motor rated rotational speed (motor nameplate)
H :
Motor constant 1 (torque boost)
H :
Motor constant 2 (no-load current)
H :
Motor constant 3 (leak inductance)
H : Motor constant 4 (rated slip)
To use vector control and automatic torque boost, motor constant setting (motor tuning) is required. The motor
constant can be set in any of the following three ways.
After setting by one of three ways, drive the motor.
Selection 1: Using the automatic torque boost (CW) to make the setting of the motor control mode selection (RV)
and the auto-tuning 1 parameter (H) at a time.
Selection 2: Setting the motor control mode selection (RV) and the auto-tuning 1 parameter (H) individually.
Selection 3: Combining the motor control mode selection (RV) and manual tuning.
[Selection 1: Setting by automatic torque boost]
This is the easiest of the available methods. With the automatic control parameter, you can set the automatic torque
boost, the sensorless vector control and the auto-tuning 1 parameter at a time.
Set the automatic torque boost
CW
=
(Automatic torque boost+auto-tuning 1)
Set the automatic torque boost CW=(Voltage-type vector+auto-tuning 1)
Refer to Section 5.3 for details of the setting method.
[Selection 2: Setting sensorless vector control and auto-tuning 1
independently]
This method sets sensorless vector control and auto-tuning 1 independently.
Specify the control mode selection parameter (RV) and then set auto-tuning 1.
Auto-tuning 1 H= (Auto-tuning enabled)
[Parameter setting]
Title Function Adjustment range Default setting
H Auto-tuning 1
:No auto-tuning
:Initialize motor constant ( after execution)
:Continue operation continued after auto-tuning
( after execution)
:Auto-tuning by input terminal signal
:Motor constant auto calculation ( after execution)
Note 1: When H is set to , factory default values are taken for parameters H (motor constant 1),
H (motor constant 2), H (motor constant 3), and H (motor constant 4).
Note 2: If H is set to , only auto-tuning is performed. So use this setting when the machine cannot be
operated as-is for reasons of itself after auto-tuning.
Note 3: When setting H to , or , set the base frequency XN, base frequency voltage XNX, motor's
rated voltage H and motor's rated rotational speed H in advance, as specified on the motor
nameplate. This makes it possible for the inverter to be tuned with higher precision.
Note 4: When auto-tuning cannot be made (for example, when no motor is connected), set H to to make
the inverter automatically calculate and set the motor constant.
Auto-tuning 2 H= (Self-cooled motor tuning)
Auto-tuning 2 H= (Forced-cooled motor tuning)
[Parameter setting]
Title Function Adjustment range Default setting
H Auto-tuning 2
:No tuning
:Self-cooled motor tuning
:Forced-cooled motor tuning
Auto-tuning 2 refers to the function of adjusting the motor constant automatically, while estimating the increase in the
motor temperature.
When using a motor without a cooling fan (natural air-cooling type), set H to . When using a motor with a
cooling fan (forced air-cooling type), set H to .
• Perform auto-tuning 2 along with auto-tuning 1.
• Perform auto-tuning when the motor is cold (temperature equal to the ambient temperature).
Vista de pagina 147
1 2 ... 143 144 145 146 147 148 149 150 151 152 153 ... 311 312

Comentarios a estos manuales

Sin comentarios