Toshiba Tosvert VF-AS1 Manual de usuario Pagina 143
- Pagina / 312
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
E6581301
F-31
6
6.18 Acceleration/deceleration suspend function
H :
Acceleration/deceleration
suspend function
H :
Acceleration suspend frequency
H : Acceleration suspend time
H
:
Deceleration suspend frequency
H : Deceleration suspend time
•Function
Using these parameters, acceleration or deceleration can be suspended to let the motor run at a constant
speed. There are two ways to suspend acceleration or deceleration: suspending it automatically by setting
the suspend frequency and time using parameters, and suspending it by means of a signal from an
external control device.
These parameters are useful in starting and stopping transfer equipment, textile machines (winders), and
so on.
[Parameter setting]
Title Function Adjustment range Setting value
H Acceleration/deceleration suspend function
:Disabled
:Parameter setting
:Terminal input
H Acceleration suspend frequency ~HJ Hz
H Acceleration suspend time ~ sec.
H Deceleration suspend frequency ~HJ Hz
H Deceleration suspend time ~ sec.
Note1: The acceleration suspend frequency (H) should not be set below the starting frequency (H).
Note2: The deceleration suspend frequency (H) should not be set below the stop frequency (H).
Note3: If the output frequency is lowered by a stall prevention function, the acceleration suspend function may be
activated.
1) To suspend acceleration or deceleration automatically
Set the desired frequency with H or H and the desired time with H or H, and then set
H to .
When the frequency set is reached, the motor stops accelerating or decelerating to rotate at a constant speed.
Output frequency [Hz]
H
Time [s]
H
H
H
2) To suspend acceleration or deceleration by means of a signal from an external control device
Set for the desired external signal input terminal. As long as ON signals are output, the motor continues to
rotate at a constant speed.
Output frequency [Hz]
Time [s]
Terminal board input
Ex.) When using the RR/S4 terminal as the acceleration/deceleration suspend terminal
Title Function Adjustment range
Example of setting
H Input terminal function selection 8 (RR/S4) ~
- E6581301Ԙ 1
- I. Safety precautions 3
- Danger 4
- II. Introduction 9
- E6581301 11
- - Contents 11
- 1. Read first 17
- 1.3.1 Names and functions 18
- 1) Outside view 18
- 1.3.2 Detaching the cover 25
- 1.4 Notes on the application 30
- 1.4.1 Motors 30
- 1.4.2 Inverters 32
- ■ Disposal 32
- Warning 33
- 1.4.4 Installation 35
- ■ Installation environment 35
- ■ How to install 36
- 2. Connection equipment 41
- 2.2 Standard connections 43
- 2.3 Description of terminals 48
- 3. Operations 55
- Status monitor mode 56
- Standard monitor mode 56
- (when the power is turned on) 56
- Setting monitor mode 56
- Deceleration 57
- 3.2.2 Panel operation 61
- 4.1 How to set parameters 64
- 5. Basic parameters 67
- CW : Automatic torque boost 69
- ■ Preset speed operation 74
- + The inverter is factory 75
- +To save the frequency 75
- HE and the set 75
- 5.6 Selecting control mode 77
- 2) Decreasing output voltage 78
- 3) Increasing starting torque 78
- 5.8 Base frequency 81
- 5.9 Maximum frequency 82
- Estimation of temperature 90
- 5.17 PWM carrier frequency 96
- Warning 97
- Surge killer 103
- 5.20 Standard default setting 107
- ( ) 109
- 5.22 EASY key function 110
- 6. Extended parameters 113
- 6.2 Input signal selection 115
- Internal command 116
- Servo lock status 120
- Command selected 123
- Operation frequency 125
- 6.8 DC braking 126
- 6.10 Jog run mode 131
- Jumping width 2 135
- Jumping width 1 135
- 6.14.1 Retry function 136
- 6.15 Drooping control 139
- Load portion torque input 141
- 6.20 PID control 145
- 6.22 Setting motor constants 148
- Setting motor constants 150
- 6.24 Torque control 152
- 6.25 Torque limit 154
- Positive torque 155
- Negative torque 155
- • Function 158
- 6.31 Pattern operation 163
- 6.32 Preset speed mode 165
- 6.33 Protection functions 166
- 6.33.3 Emergency stop 167
- H : Emergency stop 167
- 6.34 Override 175
- 6.35 Adjustment parameters 177
- Function 179
- ■ Example of setting 1 181
- ■ Example of setting 2 181
- 6.37 Tracing functions 183
- Trace data 1 184
- Trigger input 184
- 6.38 Communication function 187
- 1) 2-wire RS485 188
- 2) 4-wire RS485 190
- Host computer 191
- 6.39 My function 193
- 6.40 Traverse function 194
- 7.1 External operation 195
- B-contact switch 196
- Input terminal 196
- Inverter 196
- Programmable controller 197
- 7.2.4 Analog input filter 203
- 8.2 Monitoring the status 210
- 8.4.1 Trip code display 216
- 9.1.1 EMC directive 221
- Contact your supplier 222
- Use the 224
- EMC FILTER 226
- Ferrite core 1 227
- Shielded cable or [Note 1] 227
- Noise cut plate 228
- AIC, Fuse and Wire sizes 229
- Ｅ６５８１３００ 232
- Note on wiring 233
- 11. Table of parameters 239
- 12. Specifications 285
- E6581301 286
- ■ Outside dimensions and mass 289
- (Installation dimension) 290
- Before making a service call 295
- Cautions about cleaning 303
- 14.2 Periodical inspection 304
- ■ Check items 304
- 15. Warranty 307
- Warning 309
Relacionado con productos y manuales para Herramientas Toshiba Tosvert VF-AS1
Herramientas Toshiba HX7 Manual de usuario
(6 paginas)
(6 paginas)
Herramientas Toshiba 1500 Plus Manual de usuario
(31 paginas)
(31 paginas)
Herramientas Toshiba G8000 Manual de usuario
(79 paginas)
(79 paginas)
Herramientas Toshiba 4200FA CT/XT Manual de usuario
(68 paginas)
(68 paginas)
Herramientas Toshiba Tosvert RS485 Manual de usuario
(73 paginas)
(73 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales